This is a SUPER NICE Kubota M8560D Tractor with LA1353A front end loader with 175 hours. 4X4 with cab/air/heat, etc. 3 pt hitch. An 80 year old gentleman bought it new, used it very little, and decided that it was too much tractor for him. Please click on the individual pictures to zoom in as they tell the story. The bucket looks like it has hardly been used. Tires are excellent. 6 rear hyd outlets. Cab floor is a little dirty from getting in and out but will clean up nice. Everything works like it should. Cranks and runs just like new. Serial number is in one of the pictures if you want to contact Kubota for the year model. I have included the specs below the pictures for the tractor and loader. $49550 (tractor only).
Also have a 15′ Bush-Whacker flex wing rotary cutter with side curtain chains in the same condition as the tractor. You can view the Bush-Whacker by CLICKING HERE. Sells for $13000 new. Will sell this one for $7500. Or take the tractor and bush hog together for $54900.
Kubota M8560HDC:
4WD Cab 8-speed
Engine: 3.8L 4-cyl diesel
Fuel Capacity: 29.1 gal
3-Point Hitch: Type II
Rear lift (at 24″): 4630 lbs
Rear Arms: telescopic lower link ends
Power Take-off (PTO):
Rear PTO: independent
Clutch: electro-hydraulic
Rear RPM: 540
Dimensions & Tires:
Cab Wheelbase: 88.6 inches
Weight: 6680 pounds without loader
Kubota M8560 Power:
Engine : 85.5 hp
PTO: 76 hp
Steering: hydrostatic power
Brakes: hydraulic wet disc
Cab: Optional Ultra Grand Cab with air-conditioning.
Hydraulics:
Valves: 3
Cab Pump flow: 17 gpm
Electrical:
Ground: negative
Charging system: alternator
Cab Charging amps: 60
Loader type: Kubota LA1353A
Height (to pin): 145.7 inches
131.9 inches (power position)
Clearance, dumped bucket: 110.6 inches
94.7 inches (power position)
Dump reach: 29.1 inches
45.2 inches (power position)
Dump angle: 52
64 (power position)
Reach at ground: 87.9 inches
Rollback angle: 40
Lift to full height (at 500mm): 2866 lbs
2977 lbs (power position)
Raise time to height: 4.6 s
Bucket dump time: 2.2 s
Lowering time: 3.1 s
Rollback time: 2.6 s
BUSH-WHACKER MD-180
Gearboxes — 120 HP, base mounted, 1:1.47 ratio. One dividerbox, 160 HP, base mounted. All gearboxes have malleable housings, forged alloy steel, carburized and hardened gears and shafts, tapered and ball bearings. 6 splined 1 3/8″ input shaft, 2 3/8″ output shaft on spindle boxes.
Drive Shafts — Shielded PTOs made from finest quality propeller shaft materials and needle bearing universal joints. Category 6 80-degree constant velocity main drive shaft, Category 4 intermediate and wing drive shafts.
Slip Clutch — Three heavy-duty clutches with spring type adjustment and two friction discs.
Blades — 1/2″ by 4″ material, alloy spring steel, airlift design. Free swinging when encountering obstructions. 8″ overlap for better
cutting. Blade tip speed: 15,500 FPM.
Wheels — Four solid rubber tires standard. Independent shock absorbing system for all wheel axles. Cutting height adjustable from 2″ to 15″.
Dimensions — Cutting width: 15′. Cutting height: adjustable from 2″ to 15″. Overall width: 190″. Overall length: 189″. Cutting height for aircraft and implement tires: 2″ to 17″.
Transportation width: 88″
Weight — Without chains and tires: 3,700 lb.
With standard tires and single curtain chains: 4,340 lb.
Bush-Whacker Special Deck — Includes a center deck which has a primary (bottom) deck of 10 gauge steel that is welded to heavy duty heavy channel structures. The smooth, easy-to-clean top deck is made of 12 gauge steel and protects the inner support frame. The wing decks are smooth, easy-to-clean 10 gauge steel.
Hydraulic Adjustments — Hydraulic lift cylinders control raising and lowering of flexible wing (winch assembly for manual wing lift is optional). Wing may be raised to 88 degrees above horizontal and lowered to 22 degrees below horizontal cutting plane. Optional: rephasing level lift systems.
Other Standard Features Include — Replaceable center and full length wing skid shoes, transport locking bars for each wing, heavy-duty tongue assembly with dual leveling rods, hydraulic hose holder, park jack for easy hookup and unhooking from tractor. Swivel clevis to relieve stress on tractor drawbar. Rubber guards front and back. Chain guards are an added option.